Cooper Security 9751 Installationshandbuch Seite 141
- Seite / 148
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
5. Testing
496964 Page 133
97: Engineer Walk Test
This function enables the engineer to test all devices on the system.
1. Enter programming mode.
2. Key in 97 Y
The display shows:
97: Walk Test
3. Open and close each alarm and tamper contact in turn.
The system gives a Chime tone each time you open and close a detector
contact. The display shows: "A:Zone:" and the zone number of every
detector you have tested, in sequence and for one second each. If you
also test the tampers on each zone, the display shows the letter "T"
against each zone number.
4. Press X to stop the Walk Test.
Note: The engineer Walk Test enables you to test all zones, including PA
zones, zone tampers, and control unit and bell tampers. The user Walk
Test does not enable you to test tampers or PA, Fire, 24-hour and
Technical zones.
199: Display Zone Circuit Resistance
This Command lets you step through the zones connected to the control unit,
viewing the resistance of the circuit connected to each. Use the 1 (down) and
3 (up) keys to step through the list of zones. The display shows the resistance
of the circuit in ohms, or O/C for open circuit.
- Contents 3
- List of Figures 7
- Page vi 496964 8
- 1. INTRODUCTION 9
- Features of the Control Unit 10
- 1. Introduction 11
- 496964 Page 3 11
- Elements of the IAS 12
- 496964 Page 5 13
- 1. Introduction 14
- Page 6 496964 14
- Expanders 15
- Page 8 496964 16
- Partitioned or Single System 17
- User Control 17
- Page 10 496964 18
- 2. TECHNICAL DESCRIPTION 19
- Outputs 20
- Compatible Equipment 21
- Control Unit PCB Layouts 21
- 2. Technical Description 22
- Page 14 496964 22
- 2. Technical Description 23
- 496964 Page 15 23
- Page 16 496964 24
- 496964 Page 17 25
- Radio Expander PCB Layouts 26
- 9960 Radio Expander 27
- Page 20 496964 28
- 3. INSTALLATION 29
- 3. Installation 30
- Page 22 496964 30
- Fitting the System 31
- Page 24 496964 32
- 3. Installation 33
- 496964 Page 25 33
- Wiring the Control Unit 34
- Keypads 35
- Page 28 496964 36
- 496964 Page 29 37
- Connecting Detector Circuits 38
- 496964 Page 31 39
- Connecting Expanders 40
- Addressing Expanders 41
- Programming Outputs 42
- Communicator 43
- Page 36 496964 44
- Statutory Information 45
- Safety Notice 46
- 496964 Page 39 47
- Page 40 496964 48
- Page 42 496964 50
- 496964 Page 43 51
- Fitting a Battery 52
- Initial Start Up 52
- 496964 Page 45 53
- Page 46 496964 54
- 4. PROGRAMMING 55
- Page 48 496964 56
- 496964 Page 49 57
- Page 50 496964 58
- 496964 Page 51 59
- Page 52 496964 60
- 496964 Page 53 61
- Page 54 496964 62
- 496964 Page 55 63
- Leaving Programming Mode 64
- Performing an Engineer Reset 64
- Re-entering Programming Mode 65
- Page 58 496964 66
- Adding and Deleting Tags 67
- To Delete a Tag 68
- 0: Country PTT Defaults 69
- Page 62 496964 70
- 496964 Page 63 71
- Page 64 496964 72
- 496964 Page 65 73
- Page 66 496964 74
- 496964 Page 67 75
- 20: Change Engineer Code 76
- 21: Zone Configuration 77
- 22: Loudspeaker Chime 77
- 23: Remote Reset 77
- Page 70 496964 78
- 28: Hide Status Display 79
- 29: Entry Alarm Delay Time 79
- 30: PA Response 79
- 31: Zone Tamper Reset 79
- 32: Keypads and Partitions 80
- 33: System Reset 80
- 34: PA Reset 80
- 35: First Circuit Lockout 81
- 36: Alarm Abort 81
- 38: System Tamper Reset 81
- Page 74 496964 82
- 40: System Auto Rearm 83
- 41: Bell Delay 84
- 42: Bell Duration 84
- 43: Level A Entry Time 84
- 45: Entry/Exit Tone Volume 85
- 46: Tamper Alarm Response 85
- 49: Not used 86
- 50: CSID Code 86
- 51: Set Time and Date 87
- 52: Omit Alarm 87
- 53: Abort Reset 87
- 55: Not used 88
- 59: External Sounder Tamper 89
- 64: Level B Entry Time 90
- 66: Forbikobler Partitions 91
- 67: Forbikobler Approved 91
- 68: Forbikobler Door Timer 92
- 69: Forbikobler Door Locking 92
- 496964 Page 85 93
- 74: Level C Entry Time 94
- 496964 Page 87 95
- 78: Level D Entry Time 96
- 80: Forbikobler Chime 97
- 81 to 84: Output n Type 97
- Page 90 496964 98
- 86: Dual Ply Entry Warning 99
- 4. Programming 100
- Page 92 496964 100
- 98: Load Full Defaults 101
- 99: Leave Programming Mode 101
- 100: Not used 101
- 101: Call Mode 102
- 102: Not used 102
- 104: Not used 103
- 105: Static Test Call 103
- 103: Reporting Type 103
- 106: Line Fault Response 104
- 107: Not used 104
- 108: Dynamic Test Call 105
- 110: Download Mode 105
- 111: Modem Speed (9851 only) 106
- 112: Rings to Answer 106
- 113: Answer on One Ring 106
- 114: Access Mode 107
- 117: Account Number 108
- 121: Fast Format Channels 109
- 123: Report Restores 110
- 124: Reverse Open/Closed 110
- 126: Select Language 111
- 127: Not used 111
- 130: Not used 112
- 131: SIA Report Mode 112
- 134 to 142: Not used 115
- 144 to 150: Not used 116
- 159: Invert Plug-by Outputs 117
- 160: Confirmed Alarm Timer 117
- Page 110 496964 118
- 165 to 169: Not used 119
- 176 to 179: Not used 120
- 180: Print Log (9851 only) 121
- 181: Enable Guard Code 121
- 183: Set Display Line 2 121
- 185: Keyswitch Auto Reset 122
- 186: Set Home Beep Calls 122
- 187 to 190: Not used 122
- 4. Programming 123
- 496964 Page 115 123
- 200: Forbikobler Entry Timer 124
- 496964 Page 117 125
- Using a Partitioned System 126
- Programming Partitions 127
- Common Areas 129
- Page 122 496964 130
- 496964 Page 123 131
- Page 124 496964 132
- 496964 Page 125 133
- ACPO DD243: 2002 Compliance 134
- Alarm Filtering 135
- Page 128 496964 136
- 5. TESTING 137
- Event Log Messages 138
- 91 to 96: Testing Outputs 140
- 97: Engineer Walk Test 141
- 5. Testing 142
- Page 134 496964 142
- 496964 Page 135 143
- Page 136 496964 144
- Index 145
- 496964 Page 137 145
- Page 138 496964 146
- Declaration of Conformance 147
- 9751/9752/9851 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Cooper Security 9751
(88 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern