Cooper Security 9751 Betriebsanweisung Seite 27
- Seite / 96
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2. Programming Commands
497096, issue 3 Page 21
Notes on Lock Set:
1. Do not assign the keypad to more than one partition. Do not connect more than one
lock switch (or any other device) to the keypad ET terminals. In a single system, do
not attempt to fit two lock switches.
2. To set the system, the user first enters their access code at a keypad or operates a
keyswitch. The control unit starts to emit the exit tone. The exit time is infinite in this
option. The user then operates the Final Exit zone and turns the key in the lock
switch to "locked". The system sets 7–12 seconds after the lock switch contacts
open; the delay is set with Command 182 (see page 63).
3. To unset the system, the user turns the lock switch to "unlocked" (which closes the
contacts). The keypads start to emit a continuous tone; this is not affected by
PD6662 / pr EN 50131-1: 2004, as the possession of a key indicates an authorised
user. At this point, the user can lock the lock switch again without causing an alarm.
When the user opens the Final Exit zone, the control unit starts the entry timer. The
user completes entry by unsetting the system in the normal way.
4. When the user unlocks the lock switch, the control unit disables Alarm
Confirmation. If the user locks the lock switch without starting the entry timer, the
control unit enables Alarm Confirmation again.
5. If an intruder opens the Final Exit door without first unlocking the lock switch, the
control unit immediately starts an unconfirmed alarm. If the intruder goes on to
violate another zone and Alarm Confirmation is enabled, the control unit sends a
confirmed alarm.
40: System Auto Rearm
This command sets the number of times that the system will rearm all closed
zones when the bell duration expires. If you select option 0, the system will
not rearm (it will go into alarm only once). Select option 1 to rearm once, 2 to
rearm twice, 3 to rearm three times or 4 to rearm every time the bell duration
expires.
Use this command in conjunction with Command 35, First Circuit Lockout.
If the system has rearmed, the control unit gives an audible internal alarm
instead of the normal entry tone when a user enters the premises through the
Entry Route.
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Cooper Security 9751
(24 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern