Cooper Security 9751 Betriebsanweisung Seite 15
- Seite / 96
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2. Programming Commands
497096, issue 3 Page 9
Value Type Description
05 Final Exit (FE) Zones of this type must be the first to be activated on entry. You
can use them to set the system using the Final Door Set exit
mode. Use Command 39 to set the exit mode for the zone (page
20). Use zone attribute X7 to select an entry timer for the zone
(page 12) and Commands 201–4 (page 66) to set up the entry
timers.
06 Entry Route
(ER)
Use this zone type for detectors sited between the Final Exit
door/detector and a keypad. If an "Entry Route" zone is violated
when the system is set, an alarm will occur. If the Entry/Exit
timer is running when an Entry Route zone is violated, no alarm
occurs until the Entry/Exit timer expires. Use zone attribute X7 to
select an entry timer for the zone (page 12) and Commands
201–4 (page 66) to set up the entry timers.
07 Shock
Analyser (SA)
You can apply this zone type to zones 1 to 4. The system will
not accept this type for zones 5 to 40. Use zone attribute X7 to
set the sensitivity for the zone (page 12).
08 Technical
Alarm (TC)
Use this zone type when you want to monitor equipment, for
example a freezer, without raising a full alarm. If a Technical
Alarm zone is activated while the system is set, the system
makes no audible alarm. However, when a user unsets the
system, the keypad indicates a fault. If a Technical Alarm zone
is activated while the system is unset, the system starts a pulsed
tone from the keypad. If programmed, the control unit also starts
communication. When a user enters a valid code, the keypad
stops the tone and displays the zone.
09 Keybox (KB) This zone type is for use in Scandinavia only. When a zone of
this type is required, the Installer connects the alarm wires of the
zone to a special external key box and the tamper wires to the
box enclosure switch. When someone opens the box, the
control unit logs the event and communicates it to the Alarm
Receiving Centre (ARC). The control unit also provides a Key
Box output type, which you can program with Command 151 to
trigger one of the plug-by communicator output pins.
10 Smoke
Detector (SD)
In Scandinavia only, use this type for zones connected to 12V
smoke detectors. This type is active whether the system is set or
unset, and the control unit will transmit a specific alarm to the
Alarm Receiving Centre (ARC) if triggered. The control unit also
provides a Smoke Detector output type, which you can program
with Command 151 to trigger one of the plug-by communicator
outputs. If a zone of this type causes an alarm, the user will
need to enter an access code to disarm and reset the system.
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Cooper Security 9751
(24 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern