Cooper Security 9751 Installationsanleitung Seite 26
- Seite / 96
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
20 496792
3. Installation
Detector Circuit Connections
The left hand edge of the main PCB provides 14 connectors that can be used
for up to 8 FSL zones, or 8 Closed Circuit zones. During programming use
command 21 to configure these connectors as either CC zones, or two wire
FSL zones.
Closed Circuit Zones
Figure 11 shows how to connect Closed Circuit zones. Note that there is one
tamper loop that serves all zones. The control panel provides enough con-
nectors for eight circuits. If necessary you can connect more zones to a 9954
expander (see "Connecting Expanders").
1
2
3
Zone 1
Zone 2
Global Anti-tamper
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
Tamper loop
Zone 1
Zone 2
Alarm contacts
Alarm contacts
Figure 11. Four Wire Closed Circuit Connections
FSL Connections
The control unit zone connectors provide space for up to 8 FSL zones. If
necessary you can connect more FSL zones by using 9954 expanders. Each
FSL zone is a ‘Fully Supervised Loop’ using a two wire closed loop. The loop
uses two resistors of different values to differentiate between ‘Circuit’ and
‘Tamper’ signals: a 2K2 resistor fitted in series at the end of the wired loop
(EOL-End-Of-Line), and a 4K7 resistor fitted across the alarm contact, see
Figure 12.
With the loop in a normal state and the alarm contacts closed (shorting out
the 4K7 resistor), the total resistance of the loop is 2K2. When the alarm
contacts open (removing the short from the 4K7 resistor) the resistance of
the loop increases to 6K9 and the control unit detects an alarm condition. If a
tamper device opens then the loop will be open circuit and the control unit
detects a tamper signal.
To connect a detector to an FSL loop you must wire suitable resistors to the
detector. Always check resistor colour coding before wiring resistors into
circuit, see Figure 12.
The wiring resistance of the cable to the detector (including joints) should be
restricted to a maximum of 100 ohms. The recommended maximum cable
distance per zone is 200 - 300 metres.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Cooper Security 9751
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.135 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern